Shrink Plastic and Wire Earrings Tutorial

If you are familiar with my jewelry, you may have noticed by now that I rarely use beads, if ever. I love to incorporate color into my designs, but I try to do it in a new way. I try to use different materials like nail polish, alcohol ink, liquid polymer clay, and now illustration markers. It's cool to see how many unconventional materials I can use to make jewelry. 

For this pair of earrings, I used shrink plastic film, colored with Blick brand illustration markers. These are comparable to Prismacolor markers, but are a little bit cheaper. Illustration markers are primarily alcohol based. You can use Copic as well, but my goodness those are spendy things! Or bottles of Adirondack alcohol ink and a brush would work. Oh and sharpies! I can't forget about those. 

Materials Needed:

• clear shrink film plastic
• scissors and/or paper cutters (like guillotine cutters)
• hole punch (standard three ring binder paper punch size)
• alcohol based markers or ink (Copic, Prismacolor, Blick, Sharpie, Adirondack, etc.)
• 18 gauge wire
• 8 jump rings (you can make them yourself with the wire and tools)
• wire cutter
• round nose pliers
• flat nose pliers
• earring posts with 4mm pads (Or french hook ear wires if you want to eliminate a step)
• super glue/super glue gel/E6000 glue (whichever you prefer)

To begin, cut your desired shapes out of the shrink plastic. I wanted to use long rectangular shapes. When you bake the shrink plastic, it reduces to about 20% of the original size. I did some guess work when cutting my shapes. I cut strips of the plastic, wide enough to fit a standard hole punch with a little extra plastic on the sides. I would say my longest shapes were three inches or less in length and 3/4 inch or less in width. 

I punched holes in each rectangle and then cut irregular angles from the tops of the shapes with my scissors so the shapes wouldn't be so boxy. And sorry about the flash reflection in the pictures. The lighting in my work room was not bright enough to turn off the flash.

Next, I took my illustration markers and just started doodling.

I used tinfoil to line a baking sheet and placed all of my doodled plastics on it. The directions said to bake at 250 degrees for 3 to 5 minutes. It's kind of fun to stare into the oven while the plastic shrinks. There's nothing wrong with a grown adult sitting cross-legged on the floor, staring into the oven. Silly? Yes. Wrong? No.

As you can kind of see from the last picture. The designs shrunk nicely, and the marker became more saturated and intense. The green pieces are my favorite.

Next, I made the swirly wire designs for the studs. Using 18 gauge wire and your round nose pliers, twist the wire tightly until it is wider than the post pad. I usually twist with the flat nose pliers for a better grip. Snip your wire with your wire cutter and then create a loop at the end with your round nose pliers.

Repeat this for the second piece.

If you want, you can pound the design with a chasing hammer and bench block for a flatter look, but that's totally optional.

Take your glue of choice and place a little drop on your post pad. Stick the posts to one side of your spiral designs and allow to dry according to your glue's directions. The super glue gel sets up in less than 15 minutes.

Using the cap of my super glue and more 18 gauge wire, I formed a circle for the next part of the earrings. 

Once you form the circle, twist one end with your round nose pliers to make a loop, then cut your wire from the spool. Twist the other end of the wire to make another loop like the sixth picture. I curled it into the circle. Repeat this for the second piece. 

Now, you will need your eight jump rings. You can make them yourself by following the pictures below, but you can also buy them if you want. 

Now you are ready to assemble your pieces. Using your flat nose and round nose pliers, open and attach the jump rings to your plastic pieces and connect them to the circle design. Then use the last jump ring to connect your stud spiral to the top loop of your circle design.  

There you have it. A nice pair of dangle earrings. The plastic pieces sound kind of cool when they click together as you wear them. If you have questions or comments about this tutorial, please let me know! I would love to hear from you. 

Abstract Art Paper Earrings Tutorial

If you have been following my blog, you would have seen my last tutorial for an abstract art pendant. As promised, I will show you how to make the matching earrings for the pendant. Now, the picture shows a purple pair of earrings instead of blue, but the technique is the same. I just wanted to switch up the colors, because I like variety. What do they say? Something about that being the spice of life...

Anywho, I have really fallen in love with this technique to make paper earrings. Pretty much, if you cover any paper in enough glue/mod podge/sealer of your preference, you can have a durable material for jewelry. I made a pair of earrings using scrapbook paper and it worked out perfectly, so was inspired to try using art as well. 

Materials Needed:

• Oval/circle punch of your choosing
• dimensional glaze and/or Tacky glue/Mod Podge (I like to use a gloss finish)
• small brush
• 1/8 inch hole punch
• four jump rings or 18 gauge wire, wire cutter, and round nose pliers to make your own (I will include tutorial for jump rings below)
• Earring hooks (I use titanium ear hooks since I am allergic to nickle based metals)
• art (follow this tutorial to make your own abstract art)
• cereal box or cardstock (I recommend anything higher that 100lb weight)
• flat nose pliers to assemble pieces

I used this purple pendant for color inspiration. I have made quite a few abstract art sheets during the last year, so I have plenty of colors to choose from.

As you can tell, I like to throw in some shimmer paint to make things sparkle. To make this purple art sheet, I used a purple acrylic paint, mixed with a silver paint. I usually get most of my art supplies from Dick Blick, but you can get quality acrylic paints from craft stores as well. You might pay a little more, though, so always use a coupon!

To begin, take your circle/oval punch and punch two pieces of cereal box/cardstock, and four pieces of your art paper. You will sandwich the cereal box piece between two pieces of art so that your earrings have art on each side. Using a small brush and tacky glue or Mod Podge, spread a little glue on one side of the cereal box and press your art onto it.

Repeat this step with both sides of each earring. I let the four sides dry for about 15 minutes before moving on to the next step.

From the second picture you can see that the earring is pretty thick. This will prevent the paper from warping when it dries. I made a test pair of scrapbook paper earrings without a thick center and it warped really bad and just looked ugly. Nobody wants that.

Once your glue dries enough, then take your 1/8 inch hole punch and put a hole in each earring piece. Next, using your dimensional glaze, spread a thin layer onto one side of your earrings. You could also use Mod Podge. It's up to you whether you want a glossy or matte finish, but I prefer glossy at this moment.

Let the glaze/glue dry completely before covering the back sides with more glaze/glue. I wait a couple of hours and work on other projects between glaze applications. Yay, multitasking!

Once your pieces are completely dry, you can begin assembling your earrings. If you want to make your own jump rings. Follow the pictures below.

Using your flat nose pliers. or whatever tools you prefer, open the jump rings and begin connecting your pieces. I use two jump rings per earring. 

And now you have a pair of abstract art paper earrings! If you have any questions or comments please let me know. I would love to hear what you think of this tutorial. Have you ever tried making paper earrings? 

I also made a pair from more scrapbook paper as you can see from the second pair of earrings pictured. 

If you enjoyed this tutorial, you might also be interest in the following posts:

Scrapbook Paper Earrings Tutorial

Abstract Art Pendant Tutorial

Abstract Art Pendant Earrings Tutorial

Abstract Art Pendant Tutorial

Last night, I decided to make an icy blue pendant to capture the cold Minnesota weather. As I made this, I was wrapped in a blanket cocoon, because I am quite certain my craft room barely reaches 60 degrees in the winter (technically it's still fall, but nature doesn't seem to care about that right now). Stupid old houses and their draftiness.

Materials Needed:

• 1 inch pendant tray (I used the gunmetal colored tray)
• 1 inch domed glass 
• dimensional glaze
• necklace of your choice (The website I linked has a good variety.)
• scissors
• art or photo of your choice. If you would like to use handmade art, try this tutorial. I used the method in the tutorial to make my designs for this project. I used blue paint and white shimmer paint to give the art a sparkle. 

To start, squeeze a little dimensional glaze onto the glass piece. Then place the glass onto your art. Gently push down and make sure there are no bubbles under the glass. You can use any clear glue you want in place of the dimensional glaze, if you are feeling cheap. I used Tacky glue when I first experimented with this project, and it works decently. The main difference is that dimensional glaze is less likely to create air bubbles under the glass. So if you are picky, use a dimensional glaze. 

Let the glaze dry for a while. I think I waited an hour. Then trim off the excess paper. Next you will need to seal the back of the paper with more glaze. Use the tip of the bottle to spread a small amount of glaze onto the paper. 

Let this dry for another hour or so. Next, you will put more glaze on the back of the paper. Turn the glass over, and place it into your pendant tray. Allow to dry, again. There's a lot of dry time with this project. Maybe find other things to do in the spare time. Like make a matching pair of earrings! 

I used a 24 inch gunmetal chain for this pendant. 

And would you look at that! A matching set of paper earrings. Stay tuned for that tutorial. (Update: Here it is! Abstract Art Paper Earrings Tutorial)

If you have any questions or comments, please leave them below. I would love to hear from you and see what projects you are up to! If you enjoyed working with the glass pieces, you can take a look at some of my other tutorials like the ones listed below. 

DIY Abstract Art Refrigerator Magnets

Abstract Art Pendant Earrings Tutorial (You could easily make matching earrings with this tutorial!)

Stained Glass Wire Earrings Tutorial

It snowed. I know I make the choice of living in Minnesota, but seriously. A foot of snow in November is not cool. I have not left the house for a couple of days, so I figured I better make use of my time and start making more tutorials.

Lately, I have been getting tired of making fish hook style earrings so this tutorial involves stud posts instead.

Materials Needed:

• 4 mm pad posts
• 18 gauge wire (I used silver plated copper for all the wire) 
• 16 gauge wire
• 24 gauge wire
• round nose pliers
• wire cutter
• flat nose pliers
• super glue/super glue gel/E6000 (whichever you prefer)
• clear nail polish
• alcohol ink color of your choice
• scratch piece of paper and small snippet of 24 gauge wire

This tutorial might get a little long, since I just realized how many steps there are. They are all relatively simple steps, though, so it's definitely worth it to try this pair of earrings out! 

To begin, take your 16 gauge wire and round nose pliers. I began winding my spiral with the round nose pliers. Crimp the end down with your flat nose pliers so there isn't a hole in the middle of the spiral. Then wind the spiral a couple of times with the flat nose pliers. 

Cut the spiral from the wire with enough wire on the end to wrap a loop. Using your round nose pliers, grip the end of the excess wire and twist into a loop like the first picture below. Repeat this for your second spiral.

Using the glue of your choice, glue the posts to the middle of your spirals. Leave this to dry according to the recommended dry time on your glue. My super glue gel sets in a couple of minutes.

For the next pieces of your earrings, you will use 18 gauge wire. I cut two pieces, around 3.5 inches each. Begin by forming a loop at the end of your wire with your round nose pliers. Then with your flat nose pliers, grip the wire like the third photo, and angle the wire as pictured. 

Continue using your flat nose pliers to angle the wire into a rectangle. You'll have to do some guessing when it comes to measurements. I made a couple of scrap shapes until I got this one how I wanted it. 

Once you have formed your last angle, you will wrap the excess wire near the base of your initial loop. Sorry about the blurry pictures for photos two and three. Basically, you bend the wire behind the loop, and wrap it two or three times. I use the flat nose pliers to pull my wrapping tight. 

Once your wrapping is secure, cut off the excess wire with your wire cutter. To make sure there are no sharp edges sticking out, I crimp the end of the wire with my flat nose pliers. 

For the third part of the earrings, grab your 24 gauge wire. cut two pieces, about three inches long. Using your round nose pliers, you will form the loops that go on the inside of your rectangle. Play with the wire a bit if you have never worked with it before. 

The basic idea is to wrap the wire around your round nose pliers until a loop forms, then move onto the next loop. I use the ends of my pliers so the loops aren't too big. Start about an inch into the wire so that you will have excess wire on both sides of your design to use for the next step. 

I formed five loops and fit it into my rectangle to see how it would look. As you can see, I have enough wire on each end to wrap the design around the rectangle. Using your flat nose pliers, wrap the wire, pull it tight, and then cut off the excess wire. 

Next, you will fill in the loops with nail polish and alcohol ink. I used a third hand tool to hold the earrings while I worked with the nail polish. You don't need this tool. It's just more convenient. If you use your hands instead, just make sure that you hang the earrings on something as they dry. 

Using your scrap piece of paper, mix approximately five drops of polish with one drop of ink. Mix this together with a scrap piece of wire. I didn't include the pictures of how to put the polish in the wire, so if you want more visual directions check out this link. 

Basically, you dip the wire in the colored polish so that a drop accumulates on the end. Then, place the wire inside one of the loops. The polish should stick to the sides of the wire. You can use a light circular motion to touch the insides to the loop to help deposit the polish. If the polish doesn't hold tight, and form a complete surface, try adding more polish. If that doesn't work, the loop might be too big. 

Let the polish dry completely, then move on to the assembly stage! You will need two jump rings. You can either make them yourself with 18 gauge wire or use ready-made rings. Follow the pictures below to make your own jump rings. All you need is wire, your round nose pliers, and a wire cutter. 

Using your flat nose pliers, open your jump rings and connect the loop of the stud to the loop of the rectangle. Close your jump rings, and enjoy a nice new pair of earrings. 

If you have questions or comments, please let me know! And thanks for stopping by!